|
| OIME 1500 HP AC Drilling Rig |
Call for Price |
|
Category: Drilling Rigs
Date Posted: 2007 11 10
Location: Housotn TX
Terms: cash sold as is where is
RigPlanet ID#: 461 |
|
| Description |
REFURBISHED OIME SD9E, 1500 HP DRAWWORKS AS
FOLLOWS:
WELDED STRUCTURAL STEEL FRAME AND HOUSING, DRUM WITH GROOVING FOR 1-3/8 DRILL LINE, WATER COOLED BRAKE FLANGES, FOSTER CATHEADS, TYPE 37AK SPINNING AND 24AK BREAKOUT WITH AIR CONTROLS, 42VC1200 HIGH DRUM CLUTCH, 38VC1200 LOW DRUM CLUTCH, MOTOR DRIVE CHAINS, DRUM DRIVE CHAINS, CATSHAFT DRIVE CHAIN, INDUCTION HARDENED CUT TOOTH SPROCKETS, PRESSURE SPRAY OIL LUBRICATION TO ALL CHAINS, LUBRICATION PUMP, SELF-ALIGNING MAIN SHAFT ROLLER BEARINGS, AIR CONTROLLED TRANSMISSION CLUTCHES, AIR CONTROLLED CATSHAFT DISCONNECT CLUTCH, SPINNING AND JERKLINE ROLLER ASSEMBLIES, AUXILIARY BRAKE COUPLING, WICHITA 336 AUXILIARY BRAKE
ONTROLS FOR DRAWWORKS AND WICHITA BRAKE OPERATION
1001A ELECTRIC MOTOR DRIVE ARRANGEMENT WITH TWO (2)
AMERIMEX 75Z SERIES WOUND DC TRACTION MOTORS. EACH MOTOR TO INCLUDE A 10 HP BLOWER AND JUNCTION BOX WITH LOCKOUT SWITCH.
1002 1 EACH CROWN BLOCK SAVER WITH THE FOLLOWING:
ONE (1) MANUALLY OPERATED, 4-WAY, 2-POSITION AIR VALVE FOR SELECTING NORMAL OR OVERRIDE FUNCTION.
ONE (1) TOGGLE ACTUATED, 2-WAY, 2-POSITION AIR VALVE FOR SUPPLYING AIR PRESSURE TO SET THE BRAKE AND INTERRUPT AIR SUPPLY TO THE DRUM CLUTCHES AT A PREDETERMINED SAFE HEIGHT OF TRAVELING BLOCK UPWARD TRAVEL.
ONE (1) 4 X 12 AIR CYLINDER WITH CLUTCH ATTACHMENT TO APPLY THE DRUM BRAKE INDEPENDENT OF THE MANUAL BRAKE LEVEL.
ONE (1) AIR PILOT OPERATED, 3-WAY, 2-POSITION AIR RELAY VALVE FOR SENSING WHEN THE TOGGLE VALVE HAS BEEN ACTUATED, THUS BLOCKING THE AIR SUPPLY TO THE DRUM CLUTCH SELECTOR VALVES, AND SIMULTANEOUSLY VENTING THE DRUM CLUTCHES.
ONE (1) TOGGLE VALVE MOUNTING TRACK FOR MOUNTING AND POSITIONING THE TOGGLE VALVE OVER THE DRAWWORKS WIRE ROPE DRUM.
1003 1 EACH NEW BRAKE COOLING/TRIP TANK PACKAGE WITH
THE FOLLOWING:
ONE (1) OILFIELD TYPE MASTER SKID APPROXIMATELY 40 LONG X 10 WIDE WITH LOADING HITCHES FOR TAILBOARDING.
ONE (1) APPROXIMATELY 70 BBLS. TRIP TANK WITH TWO (2) 3X2 CENTRIFUGAL PUMPS WITH MECHANICAL SEALS, EACH POWERED BY A 25 HP, 1800 RPM, 480 VOLT, 3-PHASE, 60 HZ XP AC MOTOR AND PROVISIONS FOR REMOTE START/STOP FROM DRILL FLOOR.
ONE (1) APPROXIMATELY 90 BBLS. BRAKE COOLING TANK WITH TWO (2) 3X2 CENTRIFUGAL PUMPS WITH MECHANICAL SEALS, EACH POWERED BY A 25 HP, 1800 RPM, 480 VOLT, 3-PHASE, 60 HZ XP AC MOTOR, ELECTRIC MOTOR DRIVEN RADIATOR AND THERMOSTAT SWITCH FOR AUTOMATIC CONTROL OF RADIATOR.
1004 1 EACH NEW ANCHOR, DEADLINE, HERCULES HA-131T OR EQUAL,
100,000# DEADLINE LOAD WITH BRASS FOR 1-3/8 WIRE ROPE.
1005 1 EACH NEW YC400 OR EQUAL TRAVELING BLOCK, 400-TON
CAPACITY WITH SIX (6) 50 SHEAVES GROOVED FOR 1-3/8 LINE.
1006 1 EACH NEW DG400 OR EQUAL HOOK, 400-TON CAPACITY.
1007 1 EACH NEW SL500 OR EQUAL SWIVEL, 500-TON CAPACITY.
1008 1 EACH NEW 5,000 PSI HAMMER UNION KIT TO JOIN SWIVEL TO
ROTARY HOSE.
1009 1 EACH NEW INDEPENDENT ROTARY SKID WITH A CONTINENTAL
EMSCO STYLE 27.5 ROTARY TABLE POWERED BY AN AMERIMEX 75Z SERIES WOUND DC TRACTION MOTOR WITH DUCTING TO A 10 HP BLOWER FOR COOLING. ROTARY TABLE TO BE DIRECT DRIVEN VIA A DRIVELINE.
NEW API 4F DSI 142 HIGH CANTILEVERED MAST HAVING A RATED STATIC HOOK LOAD CAPACITY OF 750,000 LBS. WITH 12-LINES STRUNG TO THE TRAVELING BLOCK.
CROWN BLOCK HAVING ONE (1) 60 DIAMETER FABRICATED STEEL FASTLINE SHEAVE AND SIX (6) 50 DIAMETER FABRICATED STEEL WORKING SHEAVES MOUNTED ON TAPERED ROLLER BEARINGS. DEADLINE ON OFF-DRILLERS SIDE.
SHEAVES GROOVED FOR 1-3/8 DIAMETER WIRELINE.
BLOCK HANGING LINE PAD-EYE.
ESCAPE LINE, 9/16 X 1.5 DERRICK HEIGHT, PAD-EYE, AND SHACKLE.
ADJUSTABLE RACKING PLATFORM HAVING A CAPACITY TO ACCOMMODATE 242-STANDS OF 5 DRILL PIPE AND 10-STANDS OF 9 DRILL COLLARS. WORKING PLATFORM AND 7 HIGH HNDRAILS TO BE INCLUDED.
MAST BELLY BOARD
SET TONG COUNTERWEIGHTS COMPLETE WITH BUCKETS, GUIDES, BLOCKS AND WIRELINES.
SET RAISING LINES WITH PULL TEST CERTIFICATES
SLINGLINE EQUALIZER UNIT
4002 1 EACH NEW API 4F DSI 25 HIGH BOX-ON-BOX SUBSTRUCTURE HAVING A CASING CAPACITY OF 750,000 LBS. AND A SETBACK CAPACITY OF 400,000 LBS. SUBSTRUCTURE DESIGNED TO ACCOMMODATE A 1500 HP ELECTRIC DRAWWORKS AND DRILLERS SIDE DOGHOUSE.
NEW TWO (2) TANK MUD SYSTEM HAVING A TOTAL CAPACITY OF 1000 BBL. TANK GENERAL CONSTRUCTION AS FOLLOWS:
THREE-RUNNER OILFIELD TYPE SKIDS 7-10 WIDE WITH OILFIELD TYPE SKID ENDS FOR TAILBOARDING. SKID EXTENSIONS DECKED WITH 1/4" PLATE.
TANK WALLS RIMMED WITH 6 SQUARE TUBING FULL LENGTH OF TANKS.
TANK SIDE AND END WALLS CONSTRUCTED OF 1/4" CRIMPED PLATE FOR RIGIDITY.
5001 1 EACH SHAKER TANK:
520 BBLS. FOUR (4) COMPARTMENT SHAKER TANK, 10 WIDE X 8 DEEP X 40 LONG MOUNTED ON A 53 LONG SKID PER ABOVE GENERAL SPECIFICATIONS AND INCLUDING:
TANK COMPARTMENTS AS FOLLOWS:
91 BBLS. SAND TRAP COMPARTMENT
143 BBLS. DEGAS COMPARTMENT
143 BBLS. DESAND COMPARTMENT
143 BBLS. DESILT COMPARTMENT
THREE (3) FULL PARTITIONS WITH EQUALIZER VALVES.
10 SKID EXTENSION TO ACCOMMODATE DESAND/DEGAS AND DESILTER PUMPS.
TOP WALKWAYS OF GRATING AROUND ALL EQUIPMENT FOR SERVICING. INCLUDES TUBING HANDRAILS AND TOE BOARDS.
REMOVABLE WALKWAY WITH HANDRAILS TO INTERMEDIATE TANK.
ONE (1) STAIR TO GROUND WITH HANDRAILS.
ITEM PART NUMBER
NUMBER QUANTITY DESCRIPTION
ONE (1) 1 DIAMETER X 25 LONG VALVED WATER WASHDOWN HOSE.
ONE (1) WATER CONNECTION TO DESILTER TROUGH.
ONE (1) WATER CONNECTION TO DESANDER TROUGH.
16 X 18 MUD DITCH WITH DUMP GATE TO EACH COMPARTMENT.
TWO (2) DERRICK FLC-504, 4-PANEL HIGH G SHAKERS TO BE SUPPLIED AND INSTALLED.
ONE (1) DERRICK DSV-10-2, 2-CONE STAND ALONE VERTICAL DESANDER TO BE SUPPLIED AND INSTALLED.
ONE (1) DERRICK S-416-S, 16-CONE STAND ALONE DESILTER TO BE SUPPLIED AND INSTALLED.
ONE (1) DERRICK VACU-FLO 1200 VERTICAL DEGASSER TO BE SUPPLIED AND INSTALLED.
ONE (1) 3 BOTTOM MUD GUN WITH BUTTERFLY VALVE IN EACH COMPARTMENT.
THREE (3) 8 BUTTERFLY VALVE CLEAN-OUT GATES ONE (1) EACH IN DESAND, DEGAS AND DESILT COMPARTMENTS.
ONE (1) 12 BUTTERFLY VALVE CLEAN-OUT GATE IN SAND TRAP COMPARTMENT.
TWO (2) 6X5 CENTRIFUGAL PUMPS WITH MECHANICAL SEALS AND 60 HP, 1800 RPM, 480 VOLT, 3-PHASE, 60 HZ XP AC MOTORS SUPPLIED AND MOUNTED ON TANK SKID EXTENSION.
ITEM PART NUMBER
NUMBER QUANTITY DESCRIPTION
ONE (1) 10 BOTTOM EQUALIZER TO SUCTION TANK.
ONE (1) 10 DITCH CONNECTION TO SUCTION TANK.
ONE (1) 6 MUD GUNNING LINE CONNECTION TO SUCTION TANK.
ONE (1) 4 WATER LINE CONNECTION TO SUCTION TANK.
ONE (1) PSI 10 HP AGITATOR SUPPLIED AND MOUNTED IN LAST COMPARTMENT OF TANK.
5002 1 EACH SUCTION TANK:
570 BBLS. FOUR (4) COMPARTMENT SUCTION TANK WITH ONE (1) 10 X 10 X 8 ACTIVE COMARTMENT, TWO (2) 10 X 11 X 8 SUCTION COMPARTMENTS AND ONE (1) 10 X 8 X 8 PILL COM[ARTMENT MOUNTED ON A 53 SKID PER ABOVE GENERAL SPECIFICATIONS AND INCLUDING:
ONE (1) PSI 10 HP AGITATOR SUPPLIED AND MOUNTED IN EACH COMPARTMENT.
FOUR (4) 3 BOTTOM MUD GUNS WITH BUTTERFLY VALVES.
FOUR (4) 8 BUTTERFLY VALVE CLEANOUT GATES
TWO (2) 10 SUCTION LINES, ONE (1) FOR EACH MUD PUMP. MUD PUMP TO BE CAPABLE OF SUCKING FROM ANY COMPARTMENT OF THE SUCTION TANK.
TWO (2) 8X6 CENTRIFUGAL PUMPS WITH MECHANICAL SEALS, EACH POWERED BY A 100 HP, 1800 RPM, 480 VOLT, 3-PHASE, 60 HZ XP AC MOTOR SUPPLIED AND MOUNTED ON TANK PORCH FOR MUD MIX.
ITEM PART NUMBER
NUMBER QUANTITY DESCRIPTION
6 SUCTION LINE IN EACH COMPARTMENT OF THE SUCTION TANK FOR MUD MIX.
6 DISCHARGE FROM MUD MIX IN EACH SUCTION TANK COMPARTMENT.
ONE (1) 6 HOPPER TO SUCK OR MIX MUD IN ANY SUCTION COMPARTMENT.
5004 1 EACH SUCTION SYSTEM:
SUCTION SYSTEM FOR TWO (2) PUMPS AS FOLLOWS:
MOUNT TWO (2) CHARGING PUMPS ON MUD PUMP SKID EXTENSION.
PROVIDE SUCTION CONNECTION FOR SUPERCHARGER PUMPS FROM SUCTION LINES.
MANIFOLD SUPERCHARGER PUMP DISCHARGE FOR CHARGING TRIPLEX PUMP AT ISOLATION VALVE IN SUCTION LINE AT PUMP.
5005 1 EACH NEW HIGH PRESSURE MUD SYSTEM:
ONE (1) 4, 5,000 LB. WP HIGH PRESSURE MUD DELIVERY SYSTEM FOR TWO (2) MUD PUMPS AS FOLLOWS:
PROVIDE 4 SCHEDULE XXH SUBSTRUCTURE LINE COMPLETE WITH HAMMER UNIONS AT BREAK POINTS AND HEAVY-DUTY CLAMPS FOR MOUNTING. HAMMER UNIONS TO BE WELD ON TYPE.
SECTION 6000 - HOUSES/TANKS/MISCELLANEOUS EQUIPMENT
ITEM PART NUMBER
NUMBER QUANTITY DESCRIPTION
6001 1 EACH NEW DRILL WATER TANK:
10-6 DIAMETER X 32 LONG TANK MOUNTED ON AN APPROXIMATELY 40 LONG OILFIELD TYPE SKID WITH LOADING HITCHES FOR TAILBOARDING.
TWO (2) MCM 3X2 CENTRIFUGAL PUMPS WITH ROPE PACKING. EACH PUMP TO BE POWERED BY A 25 HP, 1800 RPM, 480 VOLT, 3-PHASE, 60 HZ XP AC MOTOR. PUMPS TO BE MOUNTED ON TANK PORCH.
6002 1 EACH NEW PRIMARY FUEL TANK:
8 DIAMETER X 30 LONG TANK MOUNTED ON AN APPROXIMATELY 40 LONG OILFIELD TYPE SKID WITH LOADING HITCHES FOR TAILBOARDING.
TWO (2) ROPER AMD-27 GEAR PUMPS WITH 3 HP, 1800 RPM, 480 VOLT, 3-PHASE, 60 HZ XP MOTORS, LOCAL START/STOP AND FILTER SYSTEM TO BE MOUNTED ON UNIT.
6003 1 EACH NEW WORKSHOP:
8 WIDE X 38 LONG X 8 CLEAR CEILING HEIGHT WORKSHOP MOUNTED ON A 40 LONG OILFIELD TYPE SKID WITH LOADING HITCHES FOR TAILBOARDING. HOUSE TO BE FABRICATED OF Ό V-CRIMP MATERIAL. TOP OF SKID TO BE DECKED WITH 1/4" FLOOR PLATE.
ONE (1) 3 HIGH X 30 DEEP X 15 LONG WORKBENCH.
TWO (2) PERSONNEL DOORS.
WORKSHOP TO HAVE AIR CONNECTIONS FOR CUSTOMER SUPPLIED AIR TOOLS.
ITEM PART NUMBER
NUMBER QUANTITY DESCRIPTION
6004 1 EACH NEW DOGHOUSE:
8 WIDE X 34 LONG X 8 CLEAR CEILING HEIGHT MOUNTED ON A 7-10 WIDE X 40 LONG 3-RUNNER SKID WITH OILFIELD TYPE ENDS FOR TAILBOARDING. HOUSE FABRICATED OF 3/16 CRIMP MATERIAL AND SKID DECKED WITH 1/4" PLATE.
HOUSE INCLUDES:
ONE (1) PERSONNEL DOOR
TWO (2) SLIDING DOORS
ONE (1) KNOWLEDGE BOX
ONE (1) TOOL BOX/BENCH COMBINATION 4 LONG
6005 1 EACH NEW CATWALK:
5 WIDE X 18 HIGH X 60 LONG.
6006 1 LOT NEW CABLE TRAYS:
ONE (1) LOT AS NEEDED, ELECTRICAL CABLE/SERVICE TRAYS TO ACCOMMODATE AIR, FUEL, WATER, AND ELECTRICAL CABLE. TOP OF TRAYS COVERED TO PROVIDE WALKWAY.
6007 1 EACH NEW AIR POWERED DRILL LINE SPOOLER WITH DRILL LINE:
DRILL LINE SPOOLER WITH GUARD DESIGNED TO ACCOMMODATE A 7500 STEEL DRILL LINE REEL. MOUNTED ON A 7-10 WIDE X 12-6 LONG OILFIELD TYPE SKID WITH LOADING HITCHES FOR TAILBOARDING.
7500 OF 1-3/8 EIPS DRILL LINE
6008 1 EACH NEW US OIL TOOLS ACCUMULATOR UNIT AS FOLLOWS:
SIZED TO OPERATE 13-5/8-10M-CIW (U) DOUBLE, SINGLE BOP WITH 13-5/8-5M HYDRIL (GK) OR SHAFFER SPERICAL STYLE ANNULAR BOP.
ITEM PART NUMBER
NUMBER QUANTITY DESCRIPTION
220 GALLON ACCUMULATOR CAPACITY
ACCUMULATOR WILL FUNCTION ALL RAM CAVITIES AND ANNULAR AND RE-SUPPLY AUTOMATICALLY TO FULL OPERATING CAPACITY WITHIN FIVE (5) MINUTES.
6009 1 EACH NEW CLOSING UNIT/JUNK BIN SKID:
OILFIELD TYPE SKID TO BE 12 WIDE X 40 LONG WITH
LOADING HITCHES FOR TAILBOARDING.
CLOSING UNIT TO BE MOUNTED ON ONE (1) END OF THE SKID. A REMOVABLE ROOF WILL BE MOUNTED OVER THE TOP OF THE CLOSING UNIT. 1 PIPE FOR THE HYDRAULIC LINES WILL RUN DOWN THE OUTSIDE OF THE SKID.
THE JUNK BIN WILL BE ENCLOSED BY EXPANDED METAL WITH A 6 SQUARE TUBING RIM AROUND THE TOP. JUNK BIN TO HAVE ONE (1) AIR VOLUME TANK MOUNTED ON IT FOR EMERGENCY CLOSING UNIT OPERATION.
DRILL BIT STORAGE SPACE IS PROVIDED FOR AT CENTER OF SKID.
6010 1 EACH NEW HORN EQUIPMENT BLOW OUT PREVENTER SYSTEM CONSISTING OF:
ONE (1) DOUBLE BOP, 13-5/8, 5,000# HYDRIL STYLE
TYPE V
ONE (1) SINGLE BOP, 13-5/8, 5,000# HYDRIL STYLE TYPE V
ONE (1) ANNULAR BOP, 13-5/8, 5M HORN SPHERICAL
ONE (1) 13-5/8 MUD CROSS, 5,000# W/4 1/8 OUTLETS
6011 3 EACH NEW VIBRATOR HOSES:
3-1/2 ID X APPROXIMATELY 15, 5,000 LB. WP WITH 4 API WELDED CONNECTIONS. FOR CONNECTION OF MUD PUMPS TO SUBSTRUCTURE HP MUD LINES.
ITEM PART NUMBER
NUMBER QUANTITY DESCRIPTION
6012 1 EACH NEW ROTARY HOSE:
3-1/2 ID X 65, 5,000 LB. WP WITH 4 API CONNECTIONS. COMPLETE WITH SAFETY CLAMPS, CHAINS AND HAMMER UNIONS ON EACH END.
6013 1 EACH NEW WIRE LINE UNIT:
FIVE STAR RETRIVER WIRELINE UNIT WITH 15 HP, 1800 RPM, 480 VOLT, 3-PHASE, 60 HZ XP A MOTOR, ONE (1) LINE GUIDE, COUNTER AND 15,000 OF .092 WIRELINE.
6014 1 EACH NEW 36 METRIC TON BOP HANDLING SYSTEM:
INGERSOLL-RAND LIFT CHAIN BOP HANDLING SYSTEM MODEL BHS36PA2-17-15, 36 METRIC TON BOP HANDLING SYSTEM CONSISTING OF 2-18 METRIC TON GEARED AIR MOTOR POWERED HOISTS AND HAND GEARED TROLLEYS, 17 LIFT, 1.64 FPM @ 90 PSI DELIVERY. 18 METRIC TONS PER HOOK AND 3-CHAIN FALLS OF CHAIN.
6015 6 EACH NEW PIPE RACKS:
18 HIGH X 28 LONG TRIANGULAR PIPE RACK COMPOSED OF 5 PIPE WITH Ύ PLATE LEGS.
6016 2 EACH RAM DAUNTLESS-D UTILITY WINCH, 5000# SWL UTILITY LIFTING, 5000# SWL PERSONNEL LIFTING. EACH WINCH TO INCLUDE AUTOMATIC DRUM MOUNTED BAND BRAKE, MANUALLY OPERATED DRUM MOUNTED BAND BRAKE AND DRUM GUARD. WIRE ROPE STORAGE CAPACITY IS 680 OF 5/8 WIRE ROPE.
6017 1 EACH CHOKE MANIFOLD/MUD GAS SEPARATOR SKID AS FOLLOWS:
10 X 40 OILFIELD TYPE SKID WITH LOADING HITCHES FOR TAILBOARDING AND PROVISIONS FOR MOUNTING OF CHOKE MANIFOLD.
ITEM PART NUMBER
NUMBER QUANTITY DESCRIPTION
MUD GAS SEPARATOR TO BE 4 X 20. UNIT WILL SEPARATE MUD AND VENT GAS. UNIT WILL FOLD OVER THE TOP OF THE CHOKE MANIFOLD.
ONE (1) HORN EQUIPMENT 4, 5,000#, 2-1/16 CHOKE MANIFOLD COMPLETE WITH ONE (1) 5-WAY CROSS, EIGHT (8) 4-1/16 X 5,000# GATE VALVES, ONE (1) 2-1/16 X 5,000# GATE VALVE, ONE (1) 4-1/16 ADJUSTABLE CHOKE, ONE (1) STUDDED 4-WAY CROSS, 2-1/16 X 5,000# PORTS, ONE (1) 2-1/16 FLANGED MUD GAUGE, ONE (1) 2-1/16 X 5,000# ADAPTER FLANGE, ONE (1) BLANKING PLUG, ONE (1) 2, 1502 HAMMER NUT AND ALL BOLTS/NUTS FOR FLANGES. ONE (1) 5,000# HYDRAULIC CHOKE AND CONTROL PANEL TO BE INCLUDED.
PIPING FROM CHOKE MANIFOLD TO MUD/GAS SEPARATOR TO BE INCLUDED.
6018 1 LOT INSTRUMENTATION:
ONE (1) TOTCO TYPE 50 WEIGHT INDICATOR
ONE (1) TOTCO 100 ROTARY TORQUE
TWO (2) MUD PUMP SPMS (DIGITAL READOUT)
ONE (1) ROTARY RPM (DIGITAL READOUT)
ALL ABOVE TO BE MOUNTED IN TOTCO DRILLING CONSOLE
ALL ELECTRICAL INSTRUMENTATION
SECTION 7000 - RIG-UP/TEST/RIG-DOWN
ITEM PART NUMBER
NUMBER QUANTITY DESCRIPTION
7001 1 LOT MECHANICAL RIG UP:
SET AND ASSEMBLE MAST AND SUBSTRUCTURE
INSTALL ALL FLOORING AND HANDRAILS
INSTALL STAIRS AND V-DOOR
SET AND ALIGN ROTARY TABLE
SET AND ALIGN DRAWWORKS
SET AND INSTALL DOGHOUSE
INSTALL RACKING BOARD
STRING UP TRAVELING BLOCK
SET AND ALIGN EQUIPMENT INCLUDING:
MUD SYSTEM
BRAKE WATER/TRIP TANK
MUD PUMPS
WATER TANK
GENERATOR SETS
SCR HOUSE
FUEL TANK
CATWALK
WORKSHOP
CABLE TRAYS
CLOSING UNIT/JUNK BIN SKID
CHOKE MANIFOLD SKID
RAISE MAST
PROVIDE PIPE, FITTINGS, HOSES AND VALVES FOR FOLLOWING ACCESSORY SYSTEMS:
ITEM PART NUMBER
NUMBER QUANTITY DESCRIPTION
WATER SYSTEM:
PROVIDE WATER SUPPLY TO MUD SYSTEM WATER RIM AND MIXING SYSTEM SUCTION MANIFOLD
PROVIDE WATER SUPPLY TO RIG FLOOR WASHDOWN
BRAKE WATER SYSTEM:
PROVIDE WATER TO FEED AND RETURN LINES FROM BRAKE WATER TANK TO DRAWWORKS DRUM FLANGES AND WICHITA BRAKE.
FUEL SYSTEM:
PROVIDE FUEL TO FEED AND RETURN LINES FROM FUEL TANK TO GENERATOR SETS.
AIR SYSTEM:
PROVIDE AIR SUPPLY FOR ACCUMULATOR UNIT AND RIG FLOOR AIR MANIFOLD.
PROVIDE HOSE CONNECTIONS FROM RIG FLOOR AIR MANIFOLD TO DRAWWORKS CONTROL CONSOLE, AIR HOISTS AND OTHER FLOOR TOOLS.
PROVIDE AIR SUPPLY TO GENERATOR SET ENGINE STARTERS.
PROVIDE AND INSTALL THE FOLLOWING MISCELLANEOUS ITEMS:
TWO (2) AIR HOIST STANDS
TONG BACK-UP POST
HOSE HOBBLES FOR VIBRATOR AND ROTARY HOSES
ITEM PART NUMBER
NUMBER QUANTITY DESCRIPTION
7002 1 LOT ELECTRICAL RIG UP:
ALL ELECTRICAL TO CONFORM TO API RP-500B
PROVIDE AND INSTALL TWO (2) MAST LIGHT STRINGS WITH FLUORESCENT LIGHT FIXTURES AND OBSTRUCTION LIGHT.
PROVIDE AND INSTALL RIG LIGHTING PACKAGE, CONSISTING OF FLUORESCENT AND METAL HALIDE LIGHT FIXTURES FOR RIG FLOOR, MUD TANKS, UTILITY SKIDS, SUBSTRUCTURE AND HOUSES.
PROVIDE AND INSTALL POWER AND CONTROL CABLE FOR GENERATORS, DC MOTORS, DRILLERS CONSOLE, AC MOTORS AND ALL RELATED FUNCTIONS INDICATED IN THIS PROPOSAL.
7003 TESTING:
FILL MUD TANKS WITH WATER
PROVIDE LUBE PRODUCTS TO ALL MACHINERY
PROVIDE 1000 GALLONS DIESEL FUEL
CIRCULATE WATER THROUGHOUT MUD SYSTEM
RUN AIR COMPRESSORS AND PRESSURE TEST AIR MANIFOLD
PRESSURE TEST ALL HIGH PRESSURE LINES AND CONNECTIONS TO WORKING PRESSURE
PRESSURE TEST ALL LOW PRESSURE LINES TO WORKING PRESSURE
CIRCULATE THROUGH HIGH PRESSURE SYSTEM FOR MINIMUM OF FOUR (4) HOURS
ITEM PART NUMBER
NUMBER QUANTITY DESCRIPTION
RUN ALL SOLIDS CONTROL EQUIPMENT
LOAD TEST GENERATORS
RUN ALL GENERATOR SETS IN PARALLEL
TEST ALL SCR ASSIGNMENTS
7004 RIG-DOWN AND LOAD-OUT ON CUSTOMER-FURNISHED TRUCKS.
DRILLING RIG COMPONENTS TO BE BLASTED, PRIMED AND TOP COATED WITH POLYURETHANE PER CUSTOMERS CHOICE OF COLORS. |
|
rigplanet
Promote Your Page Too
Click above and become a fan of us on Facebook
|
